Free shipping over $99 | Worldwide Delivery
Bitfala
Ice machine ice-full sensor magnetic door two-wire reset switch main image on white background

Ice Machine Ice-Full Sensor Magnetic Door Reset Switch 2-Wire Reed Switch Magnetic Normally Open Universal Part Replacement Ice-Full Shutoff Switch for ICESTA, Lecon, Vester, LangTuo, Dometic Commercial Ice Machines

Unit price:
In Stock - 1000 Units

Brief Description

Ice-full sensor (magnetic door reset switch) compatible with ICESTA, Lecon, Vester, LangTuo, Dometic and other brand ice machines. Two-wire reed switch magnetic design with red 2P plug for direct connection. Solves issues like the machine not stopping when ice is full, false ice-full alarms on an empty bin, and ice overflowing.

Quantity

Fast Shipping
Secure Payment
30 Days Return

Product Overview

This is a magnetic door ice-full sensor — the "ice-full reset switch" commonly used on ice machines. The principle is simple: the switch body is mounted on the side wall of the ice storage bin, and a small magnet is attached to the ice-full baffle (or flap door). When ice piles up to the set height and pushes the baffle up, the magnet moves close to the switch, the internal reed switch closes, and the control board receives the signal to stop the machine. When the ice is removed, the baffle drops back, the magnet moves away, the switch opens, and the machine resumes ice making.

This is a two-wire universal model with a white potted housing and red 2P plug, compatible with common ice machine platforms such as ICESTA, Lecon, Vester, LangTuo and Dometic. The most common symptoms of a failed switch are "the machine keeps making ice even when full, with ice piling up and overflowing," or the opposite: "the machine reports ice-full on an empty bin and won't start."

Compatible Symptoms (How to Tell If It's Faulty)

① The machine doesn't stop when the ice bin is full, and ice pushes out and overflows into clumps; ② The machine shows ice-full and won't start when the bin is empty; ③ The machine stops when full but doesn't restart automatically after ice is removed, requiring a power cycle; ④ Multimeter test across the two wires: the contact should close (or open) when the magnet approaches — if the state doesn't change, the contact has failed. Meeting any one of these basically confirms the switch is damaged or the magnet has fallen off.

Technical Parameters

ItemParameter
TypeMagnetic door reed switch (ice-full/reset sensor)
WiringTwo-wire, red 2P plug at the end for direct connection to the control board
OperationCloses when magnet approaches, opens when it moves away (passive dry contact)
HousingWhite ABS housing, internally potted for moisture protection
Lead WireTwo-core flat cable, factory coiled; length subject to actual product
Compatible BrandsICESTA, Lecon, Vester, LangTuo, Dometic, etc. (match by wire count and mounting position)
InstallationFixed with screws/clips at the original mounting position; plug connects directly with no rewiring

Installation and Replacement Instructions

① Power off; ② Open the side panel or top cover of the ice bin and locate the small white block next to the ice-full baffle; ③ Unplug the red connector and remove the old part by unscrewing or prying off the fastener; ④ Install the new part in the same position and push the plug in fully; ⑤ After powering on, wave a magnet in front of the switch and listen for the control board relay to actuate or watch the display to confirm the signal is normal. The whole process takes about 10 minutes with no rewiring needed.

Two notes: keep the gap between the switch and magnet at about 5-10mm — too far and it won't close. Magnet polarity doesn't matter, but the mounting orientation must match the original machine.

FAQ

Q: How can I quickly confirm the ice-full switch is bad rather than the control board?
A: Unplug the connector and measure the two wires with a multimeter in continuity mode. Move a magnet close and away — there should normally be a continuity change. If it changes, the switch is good and the problem is in the control board or wiring; if there's no change, the switch has failed.

Q: Can a two-wire model replace the original three-wire model?
A: No. Three-wire versions are usually models with signal feedback or dual normally-open/normally-closed outputs, with different wiring definitions. Mixing them will cause error codes or failure to stop. Please select by the original machine's wire count.

Q: I replaced the switch but the machine still doesn't stop when full — why?
A: First check whether the magnet has fallen off, shifted or rusted (the small magnet on the baffle is the most likely to drop off), then confirm the plug is fully seated and the wire order is correct. If both are fine and it still doesn't stop, it's usually a fault in the control board's ice-full input circuit.

Q: Is this an OEM part?
A: This is an aftermarket universal replacement part, not produced by any brand's original factory. The brand names mentioned are only to indicate compatible models; the mounting position and wiring method match the original machine.

Ice-full sensor magnetic door reset switch overall view with red plug

Ice machine ice-full sensor white housing front view

Ice-full sensor wire harness and plug detail